Find a local Tasker to make you custom furniture near you

I need a qualified and experienced cabinet maker to finish few cabinets inside the van. My precious guy went to Cairns and left the job undone.

I need one customised cabinet for my kitchen, the cabinet is for under the bench top.

Need a cabinet maker / joiner to help help build a counter for our comercial space, we will supply all materials you just need to build it. Also some shelves etc

Needing a garage cabinet maker

Looking for someone to build in a bar nook (shelves, benchtop, cabinet drawer) around a wine fridge - relatively small space. attached pictures are similar to what we want and the space we are working with. Thanks

Our kitchen has a cabinet space for a microwave that is redundant (as you can see in the pictures, we use it as a storage shelf). We would like the area converted to a draw. We have cut-offs available that could be used as the shelf face (In addition to what is in the pictures. - Due date: Flexible

Looking for an experienced cabinet maker that can design and fit out a kitchen and several wardrobes. Price for consult. Price for job negotiable

Looking for a cabinet maker for a large kitchen

Require a kitchen cabinet maker to assist with cupboard above our fridge area, fridge slight too high so it wont fit in the area as required - unsure if existing can be slightly cut down to allow it to fit or maybe bottom shelf removed and doors filed down image attached your quote would be appreciated thanks

cabinet Maker required to pull down existing built-in wardrobe and rebuild in new room. current wardrobe is 3 m long and new wardrobe 2 m.

I need a cabinet maker to attach timber handles to wardrobe please. 6 X drawers 3 X doors See attached pics. Also need one picture put on a solid wall please. Thanks!

I need a laminated panel cut to size and two holes cut out for fitting in an oven and microwave

Drawers built in along the wall pictured. 302 cm wide (to the skirting board) Approx 45 cm deep Approx 90 cm high 3 sections with 3 drawers deep (9 draws total) Timber top on it, with white front. Sample 2 pics provided to get the idea.

Place a door on exiting cabinetry to create a linen closet with an additional shelving unit. Form ply provided. Picture below door where the wine rack is currently and is to open upward. Plans and measurements below.

2 x pull out drawers need their fronts fixed back on. Picture shows 1 of 2 that are exactly the same, except they are both right off now. You will need some dowell and cabinet fixings I would imagine. We have guests for dinner arriving at 6pm so must be done and dusted by then. I can't do it myself because I am committed to other projects already until 5.30pm.

I’m seeking to remove a kitchen cabinet so we can install a dishwasher. Need the cabinetry removed (I think some cabinetry like bottom panel will need cutting) and need a hole cut in the side of the remaining cabinetry for the dishwasher cables to go through to the next cabinet over under the sink. I have measured and it appears that removing the cabinet will leave the 60cm required for dishwasher. It would be great if cabinetry could also be taken away after job.

Task 1 Remove inserted grids and replace with two doors with a shelf inside each to act as a linen cupboard. Formply for doors supplied. Cupboard hinges required. Internals of grids can be repurposed to shelves. Task 2 build a desk into an existing wardobe to increase function

Looking for a skilled and experienced carpenter/cabinet maker to provide a quote to supply and install: 1. wardrobe inserts in bed room, 2. sliding doors in garage, 2400Hx3600W 3. new hinged door for lounge.

Hi We are looking for someone to work with us to plan out a cabinet solution fit for the space in the attached photos, due to limited space we are looking for a smart system that allows us storage, adjustable/flap in and out bench top and overhead storage. We’re not 100% sure on the best way forward so we need someone experienced to work with us to find and implement the right solution. The budget is just for the assigning, planning and quoting.

Approx 2 hours work. Will need own tools. Panels need to be cut onsite