Find experienced local carpenters in Brisbane

We would like open up downstairs/remove all walls. 4 posts - see pics need to be removed. Quote to install Support beams.

Job is to take out existing screws & decking boards Replace 5 joists (they were incorrectly done in LVL) with hardwood And put back existing decking boards Floating deck is approx 1.8 x 3.2 Joists are screwed into plastic footings (photo) Can reuse existing decking boards - just need the joists replaced Happy to try & remove as many screws as possible prior Also happy to pay per hour if unknown how long the job will take

Build a custom made replica of a double captain’s bed with drawers under. I have photos and design. Budget $2000 approximately. Solid cabinets please.

My dog chewed on the trim around a cabinet in my rental including some of the wood itself. I’m looking for someone to fix this up for me. Photo of guilty dog for reference

Outdoor bar has a missing panel. Need an ACM sheet cut in half, with little blocks of wood to sit it off the backing and flush against the other ACM sheet.

I’m reconfiguring my kitchen to also have an island bench including putting a stone kin on my current 33mm thick bench tops with a bull nose (I expect the bullnose will need to go) - such that it looks like a 40mm thick stone bench top. Colour: light coloured Sizes: Under East Window • 565 deep x 3795 across Sink area • 1565 across x 570 deep Return • 870 deep x 1420 across + waterfall edge (870 x 870). Note this will form a 280mm bench to be sat at. So will want stone on the inside / under side as well for the bench. Small bench • 500 x 505 + waterfall 505x870 Island bench (yet to be moved in place. Does not have existing substrate for the stone skin/veneer) • 1095 x 2100. 300 of the 1095 represents a bench. The bench is not built and so will need substrate built to facilitate the bench. Similarly 300 of the waterfall ends don't have the substrate for the bench. + waterfall 1095 x 870 (split by a post) + waterfall 1095 x 870 (with a notch at the bottom because it is across two different floor levels)

Need a cabinet maker to build a kitchen and laundry and install in Sunnybank. If you can not include the stone that is okay. I can get the stone done separately.

The IKEA METOD pantry and fridge cabinets were installed by ourselves and need help in putting the fridge and vents on the Plinth, and to flush the both pantry and fridge cabinet doors. Some shelf’s to be put inside the cabinet as well( comes from IKEA) https://www.ikea.com/au/en/p/superkall-fridge-freezer-no-frost-white-integrated-20509016/

Installation of 150mm feathered edge skirting with contact adhesive. Skirting and adhesive supplied. Room is 4900mmx4075mm. No need for cutting internal or external corners as skirting will sit flush when bent. There are 2 doors so skirting will need to be cut. Preferably this afternoon if possible.

Sanding n restain decking

We are after someone who can give our verandah and deck a light sand and couple of coats of stain. Approx 32m2 over 2 areas. See pic for dimensions and back deck area. Don’t have photos of veranda

Install tv box in bar foyer in Brisbane city. Parking available. May need to scribe to floor. Assistance with cabinet available. Need to have have tools and experience

Red wine was spilt on the carpet. It’s an old stain. Most of the colour has been removed, it’s just a light stain that needs to be to go.

Remove current kitchen island and take away. Install new IKEA kitchen island to replace made up of 3 simple IKEA cabinets (see image). Then we need a smaller frame build attached to the right of the new island for a lower waterfall section to be covered in stone (by someone else). Looking for someone to start the job ASAP.

I have an unusable fully integrated half dishwasher. I'd like to replace it with my LG full size freestanding dishwasher under the bench. Task includes: - remove old fully integrated dishwasher - remove the drawer under - remove the side panels and bottom panel to create a space where it can fit my new freestanding dishwasher (60cm X 60cm X 85cm) under the kitchen bench. - place the dishwasher under the bench - install the dishwasher. The section of the cabinet is 60cm wide, so it should fit the dishwasher. Bonus if you can close the space between the kitchen bench and the top of the dishwasher. (Kitchen bench height 87cm vs dishwasher 85cm tall) ETA of dishwasher is tomorrow Monday 7/11. So anytime after that would be awesome!

Hi There We are hoping to find a long term installer for us to refer work to, starting with this project! - Details are below: Location: Clayfield Brisbane. Measurements: 1.81 m X 0.87 m 1.87 m X 0.87 m 1.87 m X 0.87 m 1.85 m X .087 m 0.90 m X 0.87 m 2.05 m X .087 m 2.13 m X 0.87 m Total panels: 14 (plastic green walls) The glass is enclosed in aluminium , and we would like to see the panels attached to the top metal frame and scrured with small screws along the top, side, and bottoms to cover the inserted grass - as our client wants to view the grass panels.

We recently had our oven replaced but the new oven is ever so slightly taller, which now means the cover panel above it won't fit flush again. The cover panel needs to be shaved down to allow it to sit flush again. Apartment is in Hamilton, flexible with day and time as work from home.

I have an old mirror to be taken down (presumably attached to tiles via liquid nails). mirror can be broken if required then, a new cabinet to be picked up from Newstead Bunnings, and installed to wall. wall to be attached to is tiles on gyprock. the lights and power point have been removed already

2-3 extra shelves needed in this utility cupboard to make the space more functional and practical

I replaced my ice machine and the new one was wider than expected, it is about 4mm too wide for the cabinet that is intended to house it. I need the cabinet modified to fit it... it *appears* as though there is a fillet panel between the carcases that can possibly be removed which would allow more than enough room, but... I'm not cabinet maker so, I don't know how to do this and don't want to just start tearing my cabinets apart. Hope you can help.